
Jesús Manuel
Alegre Calderón
Catedrático de Universidad
Publications (97)
2022
-
Critical Review on Allowable Material Data Selection in Structural Design of Large Castings for Wind Turbine Gearboxes
International Journal of Metalcasting
-
Stress-intensity factor solutions for embedded elliptical cracks in round bars subjected to tensile load
Theoretical and Applied Fracture Mechanics, Vol. 117
-
Effect of HIP post-processing at 850 °C/200 MPa in the fatigue behavior of Ti-6Al-4V alloy fabricated by Selective Laser Melting
International Journal of Fatigue, Vol. 163
2021
-
Residual stresses in cold-formed steel members: Review of measurement methods and numerical modelling
Thin-Walled Structures, Vol. 159
-
TAFMEC special issue on hydrogen embrittlement of metallic materials: Fatigue and fracture
Theoretical and Applied Fracture Mechanics
-
Stress-intensity factor solutions for the simulation of fish-eye fatigue crack growth in round bars subjected to tensile load
Procedia Structural Integrity
-
Soluciones del factor de intensidad de tensiones para fisuras elípticas internas en barras cilíndricas sometidas a esfuerzos de tracción
Revista española de mecánica de la fractura, Núm. 2, pp. 73-78
-
Numerical reinterpretation of hydrogen permeation tests with residual stresses and consequences in crack modelling
Revista española de mecánica de la fractura, Núm. 1, pp. 27-32
-
Influence of non-homogeneous microstructure on hydrogen diffusion and trapping simulations near a crack tip in a welded joint
Theoretical and Applied Fracture Mechanics, Vol. 112
-
Influence of atmospheric plasma spray parameters (APS) on the mechanical properties of Ni-Al coatings on aluminum alloy substrate
Metals, Vol. 11, Núm. 4
-
Fracture toughness of coarse-grain heat affected zone of quenched and tempered CrMo steels with internal hydrogen: Fracture micromechanisms
Engineering Fracture Mechanics, Vol. 241
2020
-
Correction to: Analysis of the Influence of the Thickness and the Hole Radius on the Calibration Coefficients in the Hole-Drilling Method for the Determination of Non-uniform Residual Stresses (Experimental Mechanics, (2019), 59, 1, (79-94), 10.1007/s11340-018-0433-0)
Experimental Mechanics
-
Simulation of hydrogen permeation through pure iron for trapping and surface phenomena characterisation
Theoretical and Applied Fracture Mechanics, Vol. 110
-
Influence of charging conditions on simulated temperature-programmed desorption for hydrogen in metals
International Journal of Hydrogen Energy, Vol. 45, Núm. 43, pp. 23704-23720
-
Analysis of hydrogen permeation tests considering two different modelling approaches for grain boundary trapping in iron
International Journal of Fracture, Vol. 223, Núm. 1-2, pp. 17-35
2019
-
Impresión 3D como herramienta docente en asignaturas de Resistencia de Materiales
IN-RED 2019: V Congreso de Innovación Educativa y Docencia en Red
-
Mechanical behaviour of stamped aluminium alloy components by means of response surfaces
Materials, Vol. 12, Núm. 11
-
Cold isostatic pressing to improve the mechanical performance of additively manufactured metallic components
Materials, Vol. 12, Núm. 15
-
Application of the hole-drilling method for the evaluation of residual stresses near rounded ends
Journal of Strain Analysis for Engineering Design, Vol. 54, Núm. 7-8, pp. 424-430
-
Analysis of the Influence of the Thickness and the Hole Radius on the Calibration Coefficients in the Hole-Drilling Method for the Determination of Non-uniform Residual Stresses
Experimental Mechanics, Vol. 59, Núm. 1, pp. 79-94